Drift Car Brake System With Proportion Valve Diagram

Engineering consultants specialising in braking systems, other engineered systems, specifications, component integration, safety critical systems etc.

Brake Calculations

There are many books on brake systems but if you need to find a formula for something in particular, you never can. This page pulls them together with just a little explanation. They should work for any two axle vehicle but it's YOUR RESPONSIBILITY to verify them. Use them at your risk.....

VEHICLE DYNAMICS
Static Axle Load Distribution
Relative Centre of Gravity Height
Dynamic Axle Loads (Two Axle Vehicles Only)

STOPPING THE VEHICLE
Braking Force
Wheel Lock
Brake Torque

FOUNDATION BRAKE
Disc Effective Radius
Clamp Load
Brake Factor

GENERATING BRAKING
System Pressure
Servo Booster
Pedal Force

REAL LIFE DECELERATION & STOPPING DISTANCE

BRAKE HEATING
Stop Energy
Kinetic Energy
Rotational Energy
Potential Energy
Braking Power
Dry Disc Temperature Rise
Single Stop Temperature Rise
Fade Stop Temperature Rise

PARKING ON AN INCLINE
Axle Loads
Traction Force

LOSSES FROM CABLE OPERATED BRAKES

HYDRAULIC BRAKES
Brake Fluid Volume Requirements
Foundation Brake Requirements
Pads Compressibility
Rubber Hose Expansion
Steel Pipe Expansion
Master Cylinders Losses
Fluid Compression

DYNAMOMETER INERTIA

------------------------------------------------------------------------------------------------------

VEHICLE DYNAMICS

Static Axle Load Distribution

Note: this changes with the loading of the vehicle so laden and unladen figures are often different.

Relative Centre of Gravity Height

Dynamic Axle Loads (Two Axle Vehicles Only)

The changes in axle loads during braking bears no relationship to which axles are braked. They only depend on the static laden conditions and the deceleration.

Note: The front axle load cannot be greater than the total vehicle mass. The rear axle load is the difference between the vehicle mass and the front axle load and cannot be negative. It can lift off the ground though. (Motorcyclists beware)!

STOPPING THE VEHICLE

Braking Force

The total braking force required can simply be calculated using Newton's Second Law.

Wheel Lock

The braking force can only be generated if the wheel does not lock because the friction of a sliding wheel is much lower than a rotating one. The maximum braking force possible on any particular axle before wheel lock is given by:

Brake Torque

Having decided which wheels will need braking to generate sufficient braking force the torque requirements of each wheel need to be determined. For some legislation the distribution between front and rear brakes is laid down. This may be achieved by varying the brake size or more likely using a valve to reduce the actuation pressure.

FOUNDATION BRAKE

Disc Effective Radius

The effective radius (torque radius) of a brake disc is the centre of the brake pads by area.
For dry discs it is assumed to be:

For full circle brakes it is:

Note: the difference is because full circle brakes contact on the full face but caliper pads are not usually a quadrant but have square sides (Given the variability of friction the difference is not important in practice).

Clamp Load

The clamping load is assumed to act on all friction surfaces equally. For dry disc brakes it doesn't matter whether the brake is of the sliding type or opposed piston. Newton's Third Law state every force has an equal and opposite reaction and a reaction force from a sliding caliper is the same as an opposed piston one.

Brake Factor

Ball ramp brakes have a self servoing effect rather like a drum brake. The brake factor multiplies the output torque.

Brake Sensitivity

High factor brakes become very sensitive to manufacturing tolerances and lining friction variations. A measure of sensitivity is the amount the brake factor varies for a change in lining friction. It can be calculated:

GENERATING BRAKING

System Pressure

Pressure is a function of the required clamp load and the piston area. Remember on an opposed piston disc brake it's only the area on one side of the disc.

Servo Booster

Servo characteristics are defined graphically. The output will have at least two slopes but will also have a dead band at the bottom.

Pedal Force

The pedal ratio is calculated to the centre of the foot pad. The pedal return springs may make a significant contribution to the overall pedal force. Especially at full travel.

REAL LIFE DECELERATION & STOPPING DISTANCE

The deceleration used in calculations is a steady state one called MFDD (mean fully developed deceleration). It assumes the vehicle is either braking or not. In practice it takes a time for the system pressure to rise and the friction to build up. This is not the driver reaction time but the system reaction time. Where a calculation requires a stopping distance or an average stop deceleration then this delay must be taken into account. For calculations a linear build up over 0.6 second is used ie 0.3 second delay.

For testing the following graph show the requirements for 71/320/EEC and ECE R13.

BRAKE HEATING

Stop Energy

The energy dissipated in a stop is the sum of energy from three sources, kinetic, rotational and potential.

Kinetic Energy

Assuming the stop is from the test speed down to zero then the kinetic energy is given by:-

Rotational Energy

The rotational energy is the energy needed to slow rotating parts. It varies for different vehicles and which gear is selected however taking 3% of the kinetic energy is a reasonable assumption.

Potential Energy

The potential energy is the energy gained or lost by stopping on a hill.

Braking Power

Only when the brake is applied (but rotating) is energy being dissipated in the brake system. Some of the stop energy is dissipated in the tyre as wheel slip. Managing the ideal wheel slip is the ultimate goal of ABS development but here assume 8%. The energy to each brake depend on the number of brakes and the proportion of braking on each axle.

In order to calculate the power we need to know the brake on time:

The power is then given by:

This is the average power, the peak power at the onset of braking is double this.

Dry Disc Temperature Rise

These calculation are based on that given in the following reference:

Brake Design and Safety 2nd edition by Ruldolf Limpert

Single Stop Temperature Rise

In order to approximate the temperature rise of the disc an assumption as to where the energy is going has to be made. Initially most of the heating takes place in the disc, however this can then be rapidly cooled by surrounding components and the air stream. The calculation assumes 80% goes to the disc.

Heat flux into one side of the disc:

Single stop temperature rise is:

Fade Stop Temperature Rise

The temperature rise after repeated stopping can also be approximated, although so many variables exist it is suggested this is only used for basic optimisation work.

After a number of stops:

PARKING ON AN INCLINE

Axle Loads

When parking on an incline the lower axle has a higher load than it does on the level.

The rear axle load is the difference between the vehicle mass and the front axle load.

Traction Force

If the braked wheel is very light on an incline then it is possible the tyre will slip before the brake. Hill hold is usually required with the vehicle facing both up and down the hill. The traction force required to park the vehicle is:

Where only one of the two axles is braked the limiting slope is:

LOSSES FROM CABLE OPERATED BRAKES

Cable losses are not inconsiderable and vary depending on the number and angle of bends. A typical cable supplier uses the following calculation to calculate cable efficiency:

HYDRAULIC BRAKES

Brake Fluid Volume Requirements

When an hydraulic brake is applied fluid is required to move through the pipes. If the fluid source is a master cylinder it has a finite capacity. The following components need fluid:-

Foundation Brake Requirements

Brake fluid is required to take up running clearance.

It is also needed to compensate for lack of stiffness of the brake housing. For a disc brake the following approximation can be used:

Pads Compressibility

Pad compressibility varies between hot and cold conditions. Worst case figures are 2% cold and 5% hot at a pressure of 16MPa. The fluid required is given by:

Rubber Hose Expansion

The rubber hose expansion coefficient is usually taken as

Steel Pipe Expansion

Pipe expansion is very small and unlikely to be of interest however it should be noted that it is proportional to the cube of the diameter, so using bigger pipe than necessary on a system with a fixed fluid volume will cause longer travel for two reasons, the stiffness of the pipe and more importantly the additional fluid compression losses.

Master Cylinders Losses

Fluid losses in master cylinders increase with bore size and pressure. A reasonable assumption can be found by using the following:

Fluid Compression

Fluid compression varies with temperature and the type of fluid used.

The fluid needed to take account of compression is calculated:

It is usual to allow about 3% for trapped air in the circuits that can't be removed by bleeding. This air is squashed totally flat during braking.

DYNAMOMETER INERTIA

When testing Brakes on a dynamometer it is important to calculate the inertia requirements.
Many brakes do not run at the same speed as the wheels so it is important to understand how the brake will be mounted on the rig.
Ignoring the inertia of the wheels the required dynamometer inertia is given by